Le Lézard
Classified in: Mining industry, Business
Subject: MINING EXPLORATION UPDATE

Perseus Mining Limited Updates Mineral Resource Estimate at Bele


PERTH, WESTERN AUSTRALIA--(Marketwired - Feb. 19, 2017) -

NOT FOR DISTRIBUTION TO UNITED STATES NEWSWIRE SERVICES OR FOR DISSEMINATION IN THE UNITED STATES

Marketwired / Perseus Mining Limited (ASX:PRU)(TSX:PRU) recently completed a re-estimation of Mineral Resources for the Bélé mineral deposit on the Mahalé Exploration Licence ("Bélé") that is located within trucking distance of Perseus's currently developing Sissingué Gold Mine in Côte d'Ivoire ("Sissingué"). Details are as follows:

EXECUTIVE SUMMARY

Perseus's Managing Director and CEO, Jeff Quartermaine, commented:

"The identification and delineation of additional Mineral Resources located within trucking distance of the processing plant that is currently being constructed at Sissingué has been a prime objective of our exploration team for some time. The delineation of the Indicated Mineral Resources at Bélé announced today goes some way towards achieving that objective and as well as materially compensating for the downgrade of the Sissingué Mineral Resource announced in late 2016.

We believe that there is further significant exploration potential on both our Sissingué exploitation permit and our Mahalé exploration permit and through successful exploration we are aiming to assemble a Mineral Resource inventory that will keep the Sissingué plant fully operational for many years beyond the currently defined mine life."

BÉLÉ MINERAL RESOURCE ESTIMATE

In conjunction with the recent re-estimation of the Sissingué Mineral Resource, Snowden was requested to estimate the Mineral Resources contained in the Bélé mineral deposit that was drilled with a series of RC and diamond drill programmes during the period from 2013 to 2016. Since then, further drilling has been completed at Bélé and Snowden has reviewed this additional data and updated their earlier Mineral Resource estimate.

The revised global Mineral Resource estimate prepared by Snowden was reported in accordance with the 2012 Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code). Refer to Appendix 1 of the full press release available on www.perseusmining.com and www.sedar.com for MPR's assessment of the JORC Table 1 assessment criteria. The Mineral Resource estimate is summarised in the following table that reports the Mineral Resources by category and area, above a 0.8 g/t gold cut-off grade. The Indicated and Inferred classification categories under the JORC Code (2012) are equivalent to the CIM category of the same name (CIM, 2014).

The Bélé deposit comprises two main areas of mineralisation: Bélé East and Bélé West. In summary, the updated global Indicated Mineral Resource for the Bélé deposit is now estimated as 1.90 Mt grading at 2.0 g/t gold, containing 130,000 ounces of gold. A further 0.42 Mt of material grading at 1.8 g/t gold and containing a further 25,000 ounces of gold are classified as Inferred Resources. Details of these estimates are shown below in Table 1.

Geology

The Bélé gold deposits are located within a north-westerly striking splay of the Syama-Boundiali Greenstone Belt. At Bélé, Birimian aged rocks comprise a sequence of metasedimentary rocks and subordinate mafic volcanics that have been intruded by a nearly circular granitoid body approximately 4 kilometres in diameter. The sequence has also been intruded by numerous felsic dykes of various compositions.

Gold mineralisation at both Bélé East and Bélé West is associated with deformation zones developed at and adjacent to the margins of the granitoid intrusion. Gold is associated with disseminated pyrite and lesser pyrrhotite hosted by both mafic and felsic lithologies where they feature chlorite-sericite-calcite alteration. Vein-hosted mineralisation is rare.

Bélé West mineralisation is interpreted to extend around 1 kilometre in strike, 50 metres thickness (comprising several lodes up to 20 metres thick each) and to a depth of 150 metres. Bélé East mineralisation extends around 500 metres along strike, 130 metres thickness (comprising several lodes up to 20 m thick each) and to a depth of 170 metres. The currently defined mineralisation in both areas is open at depth but appears to be closed out along strike.

Drilling Techniques

The Bélé drill holes data includes reverse circulation ("RC"), diamond and air core ("AC") drill holes. AC drill holes were used as a guide to interpretation but were not used for grade estimation due to the poor quality of AC samples.

Drilling used for the Mineral Resource includes 274 RC drill holes for 21,937 metres, 54 diamond drill holes for 2,599 metres and 47 RC drill holes with diamond tails for 5,431 metres. Nominal drill holes spacing over the resource area is predominantly 20 metres by 40 metres to 40 metres by 40 metres at Bélé West and 20 metres by 20 metres at Bélé East. Data spacing is sufficient to establish grade and geological continuity appropriate to the resource estimation procedures and classifications applied.

Table 1: Bélé Mineral Resource Estimate - February 2017

Category Area Tonnage
(kt)
Grade
(g/t gold)
Contained
Gold (koz)
    Bélé East
Bélé East
Indicated
Laterite 33 1.9 2
Completely weathered 80 2.1 5
Partially weathered 49 1.9 3
Weakly weathered 120 2.0 8
Fresh 360 2.6 30
Total Bélé East Indicated 650 2.3 49
Bélé East
Inferred
Laterite 16 1.5 1
Completely weathered 11 1.9 1
Partially weathered - - -
Weakly weathered 19 1.5 1
Fresh 240 1.8 14
Total Bélé East Inferred 280 1.8 16
    Bélé West
Bélé West
Indicated
Laterite 38 1.7 2
Completely weathered 82 1.7 4
Partially weathered 90 1.6 5
Weakly weathered 190 1.6 10
Fresh 870 2.0 57
Total Bélé West Indicated 1,300 1.9 78
Bélé West
Inferred
Laterite 15 2.0 1
Completely weathered 18 1.7 1
Partially weathered 13 1.3 1
Weakly weathered 16 1.6 1
Fresh 77 2.0 5
Total Bélé West Inferred 140 1.8 8
    Total Bélé East and West
Total
Indicated
Laterite 71 1.8 4
Completely weathered 160 1.9 10
Partially weathered 140 1.7 8
Weakly weathered 320 1.7 18
Fresh 1,200 2.2 88
Total Indicated Resource 1,900 2.0 130
Total
Inferred
Laterite 31 1.7 2
Completely weathered 29 1.8 2
Partially weathered 16 1.4 1
Weakly weathered 36 1.6 2
Fresh 310 1.9 19
Total Inferred Resource 420 1.8 25

Notes: Mineral Resources are inclusive of any Mineral Reserves. Mineral Resources are reported to two significant figures. Rounding may cause minor discrepancies in the table. 

RC drilling (5 1/4" diameter) was usually 80 metres or less in depth. Generally RC holes only have the collar azimuth and inclination measured.

Diamond drilling was carried out using HQ in oxide and transitional rock and NQ diameter in fresh rock. All diamond holes are downhole surveyed at 30 m intervals. Downhole surveys were conducted by the drill contractors using a FlexIT tool.

Orientation of drill holes is approximately perpendicular to the strike of the geology and mineralisation at Bélé West. At Bélé East, drill holes are angled to cross the steep dip of the geological domains. At Bélé East, 12 early RC holes have been drilled along exploration fences oriented towards the east and hence sub-parallel to the mineralisation. Three of these holes intercepted significant mineralisation.

These intercepts have been verified by holes drilled in the opposite direction however, they have been removed from the database for estimation to ensure no bias occurs due to the orientation.

Sampling

All RC samples were collected at the drill site at 1 m intervals and split using a multi-stage riffle splitter. Each two consecutive samples were composited (where applicable) in one bag. Sample weights were nominally 2.5 kg and 5 kg for 1 metre and 2 metre samples respectively.

Diamond core was sawn in half using a motorised diamond blade saw, with the right half sent for assaying and the left half stored in core trays for reference. One metre samples were taken in fresh material and 1.5 metres in oxide and transition.

Both core and RC samples followed a sample preparation path involving drying, crushing and grinding. Samples were pulverised with a ring mill and thoroughly mixed on a rolling mat ("carpet roll"), and then 200 grams of sub-sample was collected. Internal laboratory checks required at least 90% of the pulp passing -75 microns. A 40 to 50 grams charge was produced for subsequent analysis of gold by fire assay.

RC samples were weighed at 1 metre intervals and recoveries back-calculated using nominal hole diameter and expected density values. Recoveries average between 60% and 75% in strongly weathered material depending on rock type, around 75% in the transition zone and >85% in fresh rock.

Recovered length of diamond samples were measured in the core trays. The overall recovery of 93% is considered good, although Snowden notes that the recovery is lower in the oxide and transitional materials.

No apparent relationship exists between sample recovery and grade for diamond drilling.

Some RC samples at depth were identified as having downhole contamination and resultant smearing of grades as a result of wet drilling in 'sticky' material, with the samples being 'hung up' in the cyclone and subsequently contaminating later samples. This issue appears to only occur in a few drill holes and is not as prevalent as what was seen at the nearby Sissingué deposit. As a result of this, all RC holes in the pit area were reviewed and any suspected of containing smeared assays were removed from the dataset prior to estimation. 277 metres from four RC drill holes (<1% of the samples) were removed due to suspected downhole contamination. In addition, 2016 drilling focused on diamond drill holes to confirm areas with RC drilling in the core of the deposit. With the exception of the issue noted above, the sub-sampling is considered appropriate and representative.

Sample Analytical Methods

All analytical work up till March 2016 was carried out by independent, commercial laboratory Bureau Veritas Minerals Laboratory ("BMVL") in Abidjan, Côte d'Ivoire. Analytical work for the recent drill holes program between November 2016 and January 2017 was carried out by independent, commercial laboratory Actlabs Burkina Faso SARL ("Actlabs") in Ouagadougou, Burkina Faso.

Two types of analysis for gold were performed, a standard fire assay using a 40 g to 50 g sub-sample, and BLEG bottle roll using a 1 kilogram sub-sample. Both methods were read by atomic absorption spectroscopy ("AAS") with a detection limit of 0.01 g/t Au. The first 13 RC holes were assayed by 1 kilogram 24-hour bottle roll, with all subsequent diamond core and RC samples assayed by 50 gram fire assay.

Quality Assurance and Quality Control

As part of the 2016 drilling program, several RC drill holes with suspected downhole smearing due to contamination at Bélé East were twinned with diamond drill holes. As a result, the suspect RC drill holes were removed as discussed previously.

Between one and two field duplicates were taken for each RC hole, preferably within mineralised intervals. The results of duplicate analysis show no bias, but only moderate repeatability. Field duplicates of diamond core were not taken as 1/4 core is considered inappropriate for comparison. Coarse crush and pulp duplicates were taken for RC and diamond samples during the recent drilling program and show good precision.

Certified reference material (blanks and standards) were submitted into the sample stream at a rate of 1 in 20 to 25 samples. Review of the standards results indicates that Actlabs tends to under call the gold standards for low grade samples by around 5% to 10%. As a result, umpire analysis was carried out on two batches using BMVL. The umpire results show that BMVL reports the low grade standards accurately. BMVL reports around a 5% to 10% higher gold grade for the low grade samples between 0.3 and 0.8 g/t gold. Results are comparable at all other grade ranges.

As a result of the above analysis, Snowden considers the Actlabs results acceptable for resource estimation, with the acknowledgement that the low grade samples are slightly conservative. Given the Mineral Resource reporting cut-off of 0.8 g/t gold, this should not have a material impact on the Mineral Resource.

With the exception of the item above, the QA/QC shows acceptable precision and no bias. Overall assaying quality is considered adequate.

Estimation Methodology

The Mineral Resource was estimated using CAE Studio (Datamine) software. Estimation was constrained within mineralisation envelopes (wireframes) defined based on a nominal 0.2 g/t gold to 0.5 g/t gold cut-off together with the geological logging and lithology interpretation. The cut-off used for the interpretation is observed as a population change in the global log-probability plot. The mineralisation domains were used as hard boundaries to control estimation.

Estimation of gold grades was carried out using ordinary kriging with top cuts applied to limit the influence of outliers. Parent blocks of 10 mE by 10 mN by 5 mRL were derived from a kriging neighbourhood analysis together with the geometry of the orebody.

Dynamic anisotropy was used for estimation, whereby the local dip and azimuth of the mineralised lodes was estimated into each block in the model and the search and variogram orientations were locally adjusted to reflect the geological orientation. This method allows the estimate to better reflect the changing orientation and undulating nature of the lodes.

The resultant estimate contains less tonnes at a higher grade within the main domains compared to the previous estimate. This is a result of the additional data allowing for a more locally accurate estimate. Application of the constraining pit shell has removed the deeper portions of the Inferred Resource, together with some blocks at the northern and southern extents. This has resulted in an overall reduction in tonnes and ounces compared to the previous Mineral Resource.

Criteria for Resource Classification

The Bélé Mineral Resource has been classified as an Indicated and Inferred Mineral Resource, in accordance with the 2012 JORC Code and the CIM Definition Standards (CIM, 2005). A range of criteria has been considered in determining this classification including geological continuity, data quality, drill holes spacing, estimation properties including kriging neighbourhood analysis to determine the appropriate block size and search strategy, and potential for economic extraction.

The above parameters were used in combination to guide the manual digitising of strings on drill sections to control the classification. Typically Indicated Resources are defined in areas of 20 metres by 20 metres drilling at Bélé East and 40 metres by 40 metres drilling at Bélé West which shows more continuity in grade.

Trial optimisation was run at a US$2,400 gold price to define the base of potentially mineable material by open pit mining.

Cut-Off Grade

The Mineral Resource has been reported by resource classification and weathering above a 0.8 g/t gold cut-off. The reporting cut-off is based on preliminary engineering work which indicates a 0.75 g/t gold to 0.85 g/t gold cut-off will be applicable for mining, depending on the degree of weathering.

Mining and Metallurgical Methods and Parameters

The metallurgical work carried out to date indicates that gold can be satisfactorily recovered from Bélé ore using conventional CIL extraction techniques as per the nearby Sissingué deposit. The work is considered sufficient to determine that the Bélé resource represents a deposit capable of economic extraction.

COMBINED SISSINGUÉ AND BÉLÉ MINERAL RESOURCES

As previously noted, the Bélé Mineral Resources are located on the Mahalé exploration permit, approximately 40 kilometres from the proposed processing plant for Sissingué and subject to confirmation of its feasibility, it is intended that this material will be processed in due course through the Sissingué process facility. The combined Sissingué and Bélé Mineral Resource is as shown in Table 2 below:

Table 2: Combined Sissingué and Bélé Mineral Resource Estimate - February 2017

Deposit Category Tonnage
('000t)
Grade
(g/t gold)
Contained
Gold (koz)
SISSINGUE Measured 4300 2.1 290
Indicated 8900 1.4 410
Measured + Indicated 13,000 1.6 700
Inferred 900 1.9 60
BELE Measured - - -
Indicated 1,900 2.0 130
Measured + Indicated 1,900 2.0 130
Inferred 420 1.8 25
SISSINGUE + BELE COMBINED Measured + Indicated 14,900 1.7 830
Inferred 1,300 1.9 85

This combined Mineral Resource compares favourably to the Measured and Indicated Mineral Resource that contained 880,000 ounces of contained gold on which Sissingué's April 2015 Definitive Feasibility Study and subsequent development decision was based.

Work is currently in progress on estimating Ore Reserves for both Sissingué and Bélé based on the revised Measured and Indicated Mineral Resource estimates and a Life-of-Mine Plan for a project encompassing both the Sissingué and Bélé Mineral Resources is expected to be completed by the end of the March 2017 quarter.

Competent Person Statement:

The information in this report and the attachments that relates to the Bélé Mineral Resource estimate is based on information compiled by Lynn Olssen a Competent Person who is a Chartered Professional (Geology) and a Member of the Australasian Institute of Mining and Metallurgy (MAusIMM), and a full time employee of Snowden Mining Industry Consultants Pty Ltd. Ms Olssen has sufficient experience which is relevant to the style of mineralisation and type of deposit under consideration and to the activity which she has undertaken to qualify as a Competent Person as defined in the JORC Code 2012 and a Qualified Person as defined in NI43-101.Ms Olssen has no economic, financial or pecuniary interest in the company. Ms Olssen consents to the inclusion in this report of the matters based on her information in the form and context in which it appears and has approved the inclusion of technical and scientific information in this report.

The information in this report that relates to Mineral Resources for the Sissingué Gold Project (SGP) was first reported by the Company in compliance with the JORC Code 2012 and NI43-101 in a market announcement released on 15 December 2016. The Company confirms that it is not aware of any new information or data that materially affects the information in that market announcement and that all material assumptions and technical parameters underpinning the estimates in that market announcement continue to apply and have not materially changed.

Caution Regarding Forward Looking Information:

This report contains forward-looking information which is based on the assumptions, estimates, analysis and opinions of management made in light of its experience and its perception of trends, current conditions and expected developments, as well as other factors that management of the Company believes to be relevant and reasonable in the circumstances at the date that such statements are made, but which may prove to be incorrect. Assumptions have been made by the Company regarding, among other things: the price of gold, continuing commercial production at the Edikan Gold Mine without any major disruption, development of a mine at Sissingué and/or Yaouré, the receipt of required governmental approvals, the accuracy of capital and operating cost estimates, the ability of the Company to operate in a safe, efficient and effective manner and the ability of the Company to obtain financing as and when required and on reasonable terms. Readers are cautioned that the foregoing list is not exhaustive of all factors and assumptions which may have been used by the Company. Although management believes that the assumptions made by the Company and the expectations represented by such information are reasonable, there can be no assurance that the forward-looking information will prove to be accurate. Forward-looking information involves known and unknown risks, uncertainties, and other factors which may cause the actual results, performance or achievements of the Company to be materially different from any anticipated future results, performance or achievements expressed or implied by such forward-looking information. Such factors include, among others, the actual market price of gold, the actual results of current exploration, the actual results of future exploration, changes in project parameters as plans continue to be evaluated, as well as those factors disclosed in the Company's publicly filed documents. The Company believes that the assumptions and expectations reflected in the forward-looking information are reasonable. Assumptions have been made regarding, among other things, the Company's ability to carry on its exploration and development activities, the timely receipt of required approvals, the price of gold, the ability of the Company to operate in a safe, efficient and effective manner and the ability of the Company to obtain financing as and when required and on reasonable terms. Readers should not place undue reliance on forward-looking information. Perseus does not undertake to update any forward-looking information, except in accordance with applicable securities laws.


These press releases may also interest you

28 mar 2024
Discovery Silver Corp. ("Discovery" or the "Company") today announced financial results for the three and twelve months ended December 31, 2023 ("Q4 2023" and "2023", respectively). The Company also provided a summary of key events since the...

28 mar 2024
Osisko Development Corp. ("Osisko Development" or the "Company") reports its financial and operating results for the three and twelve months ended December 31, 2023 ("Q4 2023"). Q4 2023 HIGHLIGHTS Operating, Financial and Corporate Updates: 2,090...

28 mar 2024
Kootenay Silver Inc. ("Kootenay" or the "Company") is pleased to announce that it has obtained a receipt for a final short form base shelf prospectus with the securities regulators in each province and territory of Canada....

28 mar 2024
Robex Resources Inc. ("Robex" or the "Company") announces today that its Board of Directors has approved the implementation of the consolidation of the issued and outstanding common shares of the Company approved by its shareholders on June 29,...

28 mar 2024
Denison Mines Corp. ('Denison' or the 'Company') is pleased to announce that it has filed its 2023 Annual Report on Form 40-F with the U.S. Securities and Exchange Commission ('SEC').  Denison's Form 40-F includes its management discussion and...

28 mar 2024
Cool Company Ltd. ("CoolCo" or the "Company") announces that it has filed its Form 20-F for the year ended December 31, 2023 with the Securities and Exchange Commission (SEC) in the U.S. Form 20-F can be downloaded from the link below, is available...



News published on and distributed by: